I2C & Serial &keypad with 20x4 display
I2C & Serial 20x4 LCD Module With Keypad Controller
This is for TWO(2) 20x4 display with controller (BV4618) and 20x4 display that you
assemble yourself. This
controller has both I2C and Serial interfaces and so there is a 5 way and 4 way
connector. Also the contrast control is surface mount. The actual controller is
shown in the text below.
Choice of colours
**** Sorry only BLUE available ****
Data sheet and resources
Size: 98 x 60 x 14
Viewing Area: 76 x 25.2
Character size: 2.95 x 4.75
The keypad is not supplied.
This can form a complete user interface using either serial or I2C communication
it will attach to any LCD display that uses the HD44780 or similar controller.
It is user configurable for displays having up to 4 lines and 80 characters.
Automatic scrolling takes place at the end of a line and also at the bottom of
the display freeing the host software form mundane tasks. The display as 3
interface options that are automatically selected when that interface is
1) Serial Interface
The serial interface has automatic Baud Rate selection form a set of pre-defined
Baud rates up to 115200. The selection is done on receiving the first character
that is carriage return (byte value 12 or \r). All bytes sent to the display
will be displayed and automatic scrolling takes place at the end of a line and
bottom of the screen. There is also a set of commands starting with ESC (byte
value 27) that are used to control the display such as clearing a line,
character positioning, clearing the display etc. Escape commands are also used
to input bytes from the keypad.
The controller will also accept input directly from a COM port and automatically
detect this. The interface is then the same as the serial interface.
3) I2C Interface
This option is automatically detected because the I2C data line has a pull up
resistor. The I2C address is user configurable in software and held in EEPROM.
Controlling the display is via commands in exactly the same way as the serial
The controller will interface to a 16 pin LCD Display module, the first 14 pins
are for the LD display and the last two pins control the back light. This will
work with all HD44789 and equivalent controllers which are fitted to just about
every character type display. The controller is set for a 16 x 2 display by
default but can be changes to any combination of lines and character widths, up
to 4 lines and 80 characters.
There is provision for up to a 4x4 (16 key) keypad. The keypad is connected to the controller via the pads provided. There is also an interrupt output that will go low when there is any key in the
16 byte buffer and goes high when all the values have been removed from the
buffer. The host software need not monitor the controller constantly as any key
pressed will be captured by the controller for later access.
This is the controller. Pins are supplied for mating with the display, serial
and I2C interface, no pins are supplied for the keypad interface.
The controller works from 3V to 5V and so is suitable for 3.3V logic, however most displays require 5V.
It also comes with the fixing kit and two angled connectors so that either
interface can be used. See additional images
- Serial Input and I2C input
- Automatic Baud rate from a selection of rates up to 112500
- Serial interface accepts RS232 input voltage levels
- I2C up to 400KHz
- VT100 superset
- Fully scrolling
- 65 byte input buffer
- 16 byte keypad buffer
- Max line length 80 char
- Max Lines 4
- keypad up to 16 switches (4x4)
- Supply voltage 3.3 to 5V DC
- Current: 6mA @ 4.7V
- Size: 55mm x 24mm
Compatible Products on the eBay Shop
|USB to I2C Convertor
||USB to I2C
What You Get
* 2 off LCD Display & Controller - Only Blue LCD's now available