This listing's P&H with Tracking, Insurance & Signature on Delivery Australia-wide is included in the price.
We are an Australian GST Registered business and a Tax Invoice is always provided.
1 x Fluke 80K-6
High Voltage Probe
Our price is $147.50 GST inclusive
delivered to your door.
That's at least $50 under retail pricing as dealers list these for $198.50 before P&H.
Pictured above is a Fluke 80K-6 Voltage Probe.
The Fluke 80K-6 High-voltage Probe is a high-voltage probe designed to
extend the-voltage measuring capability of an AC/DC-voltmeter to
6000-volts peak AC or DC Over-voltage Category I.
This means the probe
can only be used to make measurements on energy limited circuits within
Examples include high-voltage within televisions or photo
DO NOT use this probe to measure high-voltages on power
The probe provides high accuracy when used with
a-voltmeter having 10 Megohm input impedance.
A high voltage probe that allows a multimeter to measure up to 6,000V.
Intended for low energy applications only.
The 80K-6 will achieve rated accuracy when it is used with an AC/DC voltmeter having 0.25% accuracy, or better, and an input impedance of 10 megohms ±10%.
Voltage Range: 0 to 6 kV, DC or peak AC
Input Impedance: 75 megohms nominal
Division Ratio: 1000:1
DC to 500 Hz: ±1%
500 Hz to 1 kHz: ±2%
Above 1 kHz: Output reading falls: Typically -30% at 10 kHz.
Storage: -20 to 60°C
Operating: 0 to 50°C
Temperature Coefficient: 100 ppm/C
Relative Humidity: 20 - 80%
Altitude: 2000 m
Shock and Vibration:
Shock: 1 m Drop
Vibration: 5-55 Hz swept sine 3 g max.
Dimensions: 24.89 cm (9.8 in) (probe body), 5.10 cm (2.0 in) max. width
Weight: 12.7 g (45 oz)
CAN/CSA C22.2 No. 1010.2.031-94 & IEC 1010-2-031:1993,
Type B, 6 kV DC or peak AC, 4.24 kV rms AC, Over-voltage
Cat. I (Voltage derived from limited energy transformers).
The 80K-6 is compatible with any AC or DC voltmeter that has an input impedance of 10 megohms ± 10 %. Voltmeters with higher input impedances require the use of an external shunt to obtain an accurate measurement.
The 80K-6 represents a load of approximately 75 megohms to the
circuit being measured (13 mA per 1 kV). To more
accurately determine the load resistance, measure the resistance
of the 80K-6 at its voltmeter connector and multiply the measured
value by 1000.
1. Inspect the probe.
2. Connect the probe cable to a compatible voltmeter and use a shunt resistor if required.
3. Select an appropriate voltage range (1 volt reading per 1000 volt probe input).
4. Connect the ground lead of the probe to earth ground.
5. Hold the probe by the black handle and connect the probe tip to the circuit being measured.
6. Observe the voltmeter reading.
must pay for item within 5 days. Your item will be dispatched fully insured via Australia
Post to anywhere in Australia using Parcel Post with Tracking and Signature on the same or next business day at the very latest.
A GST Tax Invoice is supplied with every purchase by
specified otherwise in the body of this listing, all
items sold by me come with a 90 day replacement guarantee. This means
that if anything goes wrong with your item in the 90 days after you
receive your item, we will replace the broken down unit with a brand
new one or repair yours where the issue is minor. This guarantee does not cover misuse or abuse of any item. You must return the failed item to us and we will mail out a brand new replacement or your repaired item at our expense.
Any Problems or Queries:
contact me via eBay Messaging and I will answer your questions and
resolve any issues that you may have. Should you require a more
immediate response, don't hesitate to call Peter on
0427 524 805
for any queries.