)
These instructions are for the Large Stands only. For the Small Stands please see the appropriate listing as they are different for assembly purposes.
Some people find it ideal to super glue the peg into the stand at this stage, as it gives something more to hold onto while placing magnets.
STEP 3: Before placing and gluing any magnets, you will need to make sure of polarity. Simply take one square and one round magnet and let them join together. This is how the magnets will sit while your model is joined to the stand.
STEP 4: Start by test fitting your square magnet into one of the two small square slots at the top of the peg (as pictured). The top surface of the square magnet will sit flush with the top of the peg, leaving the round magnet sitting proud.
STEP 4a: Again, test fit your second square magnet into the other small square slots at the top of the peg (as pictured). The top surface of the square magnet will sit flush with the top of the peg, leaving the round magnet sitting proud.
STEP 5: Moving onto your model to be mounted on the stand, locate where your normal flight stand peg would go.
STEP 6: Drill the hole out to a diameter of 3mm. The best way to do this while putting minimal stress on small plastic components is to run a 3mm drill bit in a cordless drill on a backwards setting. This actually turns the excess plastic into powder under a more controlled action, rather than removing large amounts of swarf too quickly and undesirably.
STEP 6a: Using your flight stand peg as a marker (with magnets attached), locate where you want the second magnet hole to be drilled. On larger kits with more weight in one location, it is better to have the second magnet closer to that area. For example, if your skimmer/flyer has a rear turret (thus extra weight at the rear) place the second magnet hole towards the rear, when compared to the original.
STEP 7: It is recommended to use a pin vice with a 1mm drill bit to get this started. The 1mm hole will act as a pilot hole for your 3mm drill bit.
STEP 8: Drill the hole out to a diameter of 3mm. The best way to do this while putting minimal stress on small plastic components is to run a 3mm drill bit in a cordless drill on a backwards setting. This actually turns the excess plastic into powder under a more controlled action, rather than removing large amounts of swarf too quickly and undesirably.
STEP 9: Place a minimal amount of super glue in each hole you have drilled out. With the round magnets still attached to the peg as shown here (so as to keep your polarity correct) push the round magnets into the holes.
STEP 10: The peg and square magnets wont allow you to push the round magnets any further than flush with the models surface. So even if you have drilled more than 2mm, it simply isnt a problem.
STEP 11: All that is left is for you to choose which support arm to place in the center slot. Two sizes are supplied per stand, giving you the best possible outcomes, depending on the kit your are assembling.
Simply slide either arm onto the center slot, preferably adding a minimal amount of super glue to keep it in place. Support arms are also a snug fit onto the peg.
Seller assumes all responsibility for this listing.
Postage and handling
Postage cannot be calculated for your area. You can contact the seller for additional postage costs and services.
Posting cost cannot be calculated. Please enter a valid postcode.
Item location: Adelaide, SA, Australia
Posting to: Worldwide
|
There are 992 items available. Please enter a number less than or equal to 992.
Select a valid country.
|
Please enter a valid postcode.
Please enter five or nine numbers for the postcode.
|
Postage and handling |
To |
Service |
Delivery* |
|---|---|---|---|
|
Free postage
|
Australia
|
Standard Int'l Shipping
|
Varies for items posted from an international location
Seller posts within 1 day after receiving cleared payment.
|
* Estimated delivery dates include seller's handling time, and will depend on posting service selected and receipt of cleared payment. Delivery times may vary, especially during peak periods.
|
Domestic handling time
|
|---|
|
Will usually post within 1 business day of receiving cleared payment[newWindowTxt].
|
Return policy
|
Item must be returned within
|
Refund will be given as
|
|---|---|
|
14 days after the buyer receives it
|
Money Back
|
The seller is responsible for return postage costs.
|
Return policy details
|
|---|
|
Postage refunds only apply to defective items, not simply because you have changed your mind on a purchase. We can refund any postage you paid to return a defective item to us, and will we refund the postage you paid to send the defective item originally.
Any item returned as a 'defected' or 'damaged' item shall be determined to be defective or damaged by us and not the buyer. Refund will be pending the outcome of this determination.
|
Refunds by law: In Australia, consumers have a legal right to obtain a refund from a business for goods purchased if the goods are faulty, not fit for purpose or don't match description. More information at returns - opens in a new window or tab.
Payment details
| Payment method | Preferred/Accepted | Buyer protection on eBay |
|---|---|---|
|
PayPal Preferred
|
|
Seller's payment instructions
As the buyer, you have 7 days to pay for this item. Please read item description for full details.