This listing is with Insured P&H with Tracking and Signature Australia wide.
We are an Australian GST Registered business and a Tax Invoice is always provided.
_________________________________________
FLUKE 1AC-A1-II
New VoltAlert with VoltBeat
non-contact AC Voltage Detector
with sound.
Listed are these brand new Fluke 1AC-A1-II units.
These are the very latest model available from Fluke. Other cheaper units are on the market (check the photos closely for Chinese symbols and characters) but if they don't have VoltBeat Technology, they are older models.
VoltBeat Technology is a self-test feature for visual confirmation of battery and system integrity, and power on. It provides a double-flash every two seconds during normal operation.
Our price is $39.50 GST inclusive
The Fluke 1AC-A-II is a non-contact AC voltage detector that you can rely upon.
It covers AC voltages from 90V to 1000V.
When voltage is detected, the light at the nose of the pen will glow RED and you will hear a beeper sound as well.

Pictured above is the exact unit that you will be receiving.
Batteries are included.
Easy-To-Use Voltage Detector
VoltAlert 1AC-A-II voltage testers from Fluke
are easy to use - just touch the tip to a terminal strip, outlet or cord.
When the tip glows red, you know there's voltage in the line.
You will also hear an audible beep.
Electricians, maintenance, service, safety personnel, and homeowners can
quickly test for energized circuits and defective grounds on the
factory floor, in the shop or at home.
- Voltbeat™ technology and continuous self-test — so you always know it’s working
- Upon detection, tip glows and beeper sounds
- CAT IV 1000 V for added protection
- Expanded range: 90 V to 1000 V AC
- Fits in a your shirt pocket for convenience
- All outer surfaces are non-conductive for safety
- Detects voltage without metallic contact
- Quickly locates the hot, neutral and ground terminals in any receptacle
Specifications:
| Specifications |
| Operating principle |
|
Senses the steady state electrostatic
field produced by ac
voltage through insulation
without requiring contact to the
bare conductor. A red glow at
the tip and a beeping noise (if
not switched OFF) indicates the
presence of voltage. |
| | Voltage sensing ranges |
|
Nominally, 90 V AC to 1000 V
AC , 45 Hz to
405 Hz |
| | Detector tip style |
|
Blade or round, depending
on model |
| | Light source |
|
One high intensity red LED |
| | Agency Approvals |
|
c CSA us, CE, C-Tick N10140
|
| | Safety Rating | | | IP Rating | | | Operating Temperature | | | Operating humidity ranges |
| 0 % to 95 % |
(0 °C to 30 °C) |
| 0 % to 75 % |
(30 °C to 40 °C) |
| 0 % to 45 % |
(40 °C to 55 °C) |
| | Operating Altitude | | | Batteries |
|
2 AAA alkaline batteries
included |
|
Note: Product does not respond to random
electrostatic discharge.
|
|
|
|
Operating Instructions
Turning the Tester On
Momentarily press the green button. Listen for a double beep to confirm activation.
A continual VoltBeat flash visually indicates the Tester is active.
Turning the Tester Off
Press and hold the green button for more than half a second. Listen for a long halfsecond
beep to confirm deactivation of the Tester. The absence of the VoltBeat flash
indicates the Tester is inactive.
VoltBeat (System Self-Test)
VoltBeat is a self-test feature for visual confirmation of battery and system integrity, and
power on. It provides a double-flash every two seconds during normal operation.
Checking for the Presence of AC Voltage
Placing the tip of the unit near an ac voltage produces a steady glow at the tip and, if
enabled, a continual beep.
Auto Power Off
After about five minutes of non-use, the Tester automatically powers off to save battery
life. A double beep, followed by a longer, single beep, provides audible indication
that the Tester has powered off. The absence of the VoltBeat flash serves as a visual
power-off indication.
Disabling the Beeper
Disable the beeper by holding the green button down for more than two seconds during
power up. To enable the beeper again, turn the Tester off, and then turn it on.
Low Battery Indication
When the battery voltage drops below two volts, VoltBeat provides visual indication by
stopping the VoltBeat flash. Replace with two AAA (LR3) batteries.
Cleaning
Clean with damp cloth.
Our units are certified for use in Australia (Approval - N10140).
_________________________________________
Sale Conditions:
Buyer
must pay for item within 5 days. Item will be despatched fully insured via Australia
Post to anywhere in Australia using Parcel Post with tracking and signature on the same or next business day at the very latest. A GST Tax Invoice is supplied with every purchase by
default.
Guarantee:
Unless
specified otherwise in the body of this listing, all
items sold by me come with a 90 day replacement guarantee. This means
that if anything goes wrong with your item in the 90 days after you
receive your item, we will replace the broken down unit with a brand
new one or repair yours where the issue is minor. This guarantee does not cover misuse or abuse of any item. You must return the failed item to us at your
expense and we will mail out a brand new replacement or your repaired item at our expense.
Any Problems or Queries:
Please
contact me via Ebay Messaging and I will answer your questions and
resolve any issues that you may have. Should you require a more
immediate response, don't hesitate to call Peter on
0427 524 805
for any queries.
