Amal

CLIP SEAL - Quickly adjust the NEEDLE height on Mk1 carburettors (AMAL & WASSELL type). This quick-adjust CLIP SEAL allows rapid adjustment of the needle position without removing the slide or top cap. The existing metal clip is retained as support beneath the spring. Instructions included! Benefits: • Rapid adjustment of the needle position within the slide (slide in situ so great for race tuning) • Easily replace a needle with another type i.e. length or taper • Eliminates the downward airflow that is directly above the spray tube nozzle & main fuel circuit Adjustment of the needle now requires bowl removal so NP? BOWL SCREWS are recommended for simple, easy access. No more fiddly screws!

Amal type to suit any 7/8" bar application but perfect for custom bobbers and choppers. Complete set consisting of 1" single throttle assy with cable adjuster, tensioner and two Amal style ribbed rubber hand grips.

Amal parts only

This carburettor is built to a standard specification which provides approximate settings for this bore size and carburettor type. Ideal for anyone who wants to tune their machine themselves. This has not been an issue, but we must advise that there is the potential, and encourage you to check your local regulations.

Serial No: S/N525.

Serial No: S/N526.

Serial No: S/N4485.

With a bore of 22.89mm, looks to be in reasonably condition. Also a Brown&Barlow float bowl which would needs attention to the thread as it has a couple of small dents shown in photos. Plus a brass bowl top, no markings, has a spigot of 54mm.

Amal "GP" 5 and TT Slides. Total 9 Slides with Following. 3 New Large, One new (brass) small. Serial No: S/N210.

Serial No: S/N5148.

Serial No S/N 071.

Serial No: S/N2077.

Serial No: S/N382.

Serial No: S/N1058.

Serial No: S/N1469.

Serial No S/N 36.

Serial No S/N 37.

Serial No: S/N1808OM.

Serial No: S/N5308. Size is 15/16".

Serial No: S/N5483. I.D. 276AZ/IJ.

Size is 1 1/16th.

Serial No: S/N3815A.

Serial No: S/N5523.

Size is 1 1/16".

Good threads.

Suit parts. Serial No: S/N5145.

Carb I.D. 4/127. Bore size 3/4".

Serial No: S/N4486.

Serial No: S/N3265.

Genuine Amal Carburetter 930/300 Mk 1 Carb Right hand Concentric 30mm Bore Size New. The range specification is as follows: Precision manufactured forged alloy hard anodised throttle slide New precision engineered circuit Materials reduce body & slide wear & low friction & corrosion Ethonal resistant puncture proof Stay-up float Standard jetting fitted on this carb; Main jet 200 Needle jet 106 Pilot RJ17 Valve 3.

Serial No: S/N5529.

A complete repair kit for all 389 Monobloc Carburettors including needle valve gaskets/seals fuel filter needle(D) and clip pilot air screw/spring no jets supplied. This has not been an issue, but we must advise that there is the potential, and encourage you to check your local regulations.

Size is 15/16".

Serial No: S/N1903.

Good threads. Serial No: S/N620.

Serial No: S/N4398.

Serial No: S/N1360.

All Enquiries.

No float. Good threads.

Genuine Amal Carburetter 930/301 Mk 1 Carb Right hand Concentric 30mm Bore Size New. The range specification is as follows: Precision manufactured forged alloy hard anodised throttle slide New precision engineered circuit Materials reduce body & slide wear & low friction & corrosion Ethonal resistant puncture proof Stay-up float Standard jetting fitted on this carb; Main jet 200 Needle jet 106 Pilot RJ17 Valve 3.

4x Thackery double coil spring washers apply a known pre-load to carburettor/manifold joints and other critical interface. A coil gap of 0.4mm (0.016") determines the pressure applied to the joint to prevent distortion of the alloy carburettor parts. Carburettors: AMAL Mk1 Wassell Weber DCOE Dellorto DHLA etc Can be used for any joint wherever radial movement (with axial control) is specified. Threadlocking fasteners are recommended.