Digitrax Model Train Power & Controls

The DS64 Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control. The DS64 works with a wide selection of hardware. From solenoid turnout machines to slow motion motors, the DS64 hasn’t met a turnout it doesn’t like.

If the heat sink does not get enough air flow to allow for heat dissipation, the booster will eventually reach an over temperature state and shut down. A small fan blowing across the heat sink on your booster will increase the maximum sustained current output capacity of your booster.

HERE WE HAVE A NEW. DIGITRAX DT500D DUPLEX RADIO SUPER THROTTLE ,, LOCO NET ,WALKAROUND. AND MUCH MORE . AT THIS TIME.CALIF.

SE8C Plug 'N Play Signal Decoder make it easy to add prototypical signaling to your layout. The SE8C can drive as many as 32 signal heads with many popular LED signal types.

The UT4D is designed for easy to use Duplex radio control of trains and their functions. The UT4D is perfect if you're looking for a "traditional" style throttle. Their intuitive operation makes them easy for anyone to use, no need to plugin to select or dispatch your locos.

LNC82 2 x 8ft LOCONET CABLES. LocoNet Wiring is a snap with these cables. Convenient pre-made, pre-tested cables, ready to use on your layout. All LocoNet Layouts. Original Release Date.

PM42 Ready-to-Use - Power Manager for 4 Independent Power Sub-Districts. Short Circuit Management or Auto Reversing. ANY Scale Cost Effective power manager for 4 power sub-districts. See PHOTOS for more Details.

WE ARE AN AUTHORIZED DIGITRAX DEALER. WE BUY DIRECT FROM DIGITRAX. COMES WITH FULL MANUFACTURERS WARRANTY. No Worries Warranty (thru Digitrax). Designed to fit the Kato N scale P-42, PA-1 & E-8. Decoder Lock equipped.

Use this interface instead of Signal Mast Bases when you already have signals installed on your layout.

DS64 Ready-to-Use Stationary Decoder. Stationary Decoder for use with 4 slow motion, solenoid, or bi-polar turnout machines. Support for up to 8 routes. Use with any LocoNet Compatible System. Compatible with non-LocoNet DCC Systems.

LNCMK LocoNet Cable Maker Kit. Everything you need to make LocoNet Cables for your layout LT1 LocoNet Tester for testing cables prior to installation on layout. 50’ LocoNet Cable-pretested and ready to use as a single long run or to be cut into smaller lentghs.

WE ARE AN AUTHORIZED DIGITRAX DEALER. WE BUY DIRECT FROM DIGITRAX. COMES WITH FULL MANUFACTURERS WARRANTY. Use one Digitrax booster set for automatic reversing and another set for normal operation.

DT500 Advanced Super Throttle with Infrared Capability. The DT500 is designed to handle nearly every aspect of layout control. WE ARE AN AUTHORIZED DIGITRAX DEALER. WE BUY DIRECT FROM DIGITRAX. COMES WITH FULL MANUFACTURERS WARRANTY.

The UR92 is a combo Duplex Radio Transceiver and Infrared Receiver Panel. Using a UR92 means there is no need to plug in to select your loco when you are using a Digitrax Duplex equipped "D" throttle.

DH165K0 Fits Kato, Stewart, Atlas & Other. WE ARE AN AUTHORIZED DIGITRAX DEALER. WE BUY DIRECT FROM DIGITRAX. COMES WITH FULL MANUFACTURERS WARRANTY. No Worries Warranty from Digitrax. Decoder Lock equipped.

DS51K1 Features DS51K1 compatibility DS51K1 is NOT compatible with the following = 4 DS51K1 decoders are required for proper operation. WE ARE AN AUTHORIZED DIGITRAX DEALER. WE BUY DIRECT FROM DIGITRAX.

Categories we have found are as follows: Trains (all sizes) & all things pertaining to them, Remote Control vehicles, airplanes, cars, trucks, helicopters, boats & all things pertaining to them.

BDL168 - 16 Section Occupancy Detector for Loconet. Transponding decoders are detected by the RX4s and the information is fed back to LocoNet. We are an Authorized DIGITRAX Dealer. Plug 'N Play with Digitrax DCC.

SDH166D - HO Standard 1 Amp Sound Decoder with Speaker. SDH166D fits many HO locomotives. Body Size 1.28” x 0.67” x 0.25” SDH166D replaces SDH164D. We are an Authorized DIGITRAX Dealer. Digitrax SoundFX® Sound System Your locomotives will sound in scale like the real thing with SoundFX.

The UR92 is a combo Duplex Radio Transceiver and Infrared Receiver Panel. Using a UR92 means there is no need to plug in to select your loco when you are using a Digitrax Duplex equipped "D" throttle.

DT500 Advanced Super Throttle with Infrared Capability - New Product.

DS64 Quad Stationary Decoder.

DT500 Advanced Super Throttle with Infrared Capability - NEW FROM DIGITRAX! The DT500 is designed to handle nearly every aspect of layout control. We are an Authorized DIGITRAX Dealer and WE PRICE MATCH!

SDXN146K1E - Fits KATO N scale - DCC Sound Decoder with Speaker. We are an Authorized DIGITRAX Dealer. Digitrax SoundFX® Sound System. Downloadable Sound with Digitrax PR3 and SoundLoader 2.0 software.

Model AR1 auto reverse module for DCC layouts from Digitrax. Automatically change polarity of your reverse loop, reversing section or turntable. Easy 4-wire hookup. Up to 8 amp output (6 amp continuous).

Digitrax #DS64 DCC stationary accessory decoder. State of the art stationary decoder that can control multiple types of turnout machines and other stationary accessory motors and lighting. The DS64 accepts commands from LocoNet Compatible Command Stations & Throttles (via LocoNet), DCC Command Stations & Throttles (via the rails), a computer (via LocoNet), or via eight manual inputs.

Item: Dual 3/5/8 Amp AutoReversing DCC Booster. Dual 3/5/8 Amp AutoReversing DCC Booster. Easy dip switch setup. IPL updatable. Auto-Shutdown when command control signal is lost to prevent “runaway” trains.

Expandability with Digitrax LocoNet Use Zephyr Xtra as a starting point for your Digitrax LocoNet System, then add components. Your Digitrax authorized dealer will be able to assist you in choosing the “right” decoder for your layout.

We are an Authorized DIGITRAX Dealer. AR1 operates with or without LocoNet, so it is compatible with all DCC systems. AR1 Features User selectable trip current lets you adjust the AR1 to work with any scale or equipment on your layout.

AND MUCH MORE . UPPER 48 STATES ONLY ,AT THIS TIME.CALIF.

For Kato F3A F3B. Designed for Kato N scale F3A & F3B locomotives. Digitrax #DN163K0B N Scale DCC Decoder. Digitrax N scale 1.0 amp, 6 function drop-in decoder. Complete instructions included. Digitrax LocoMotion™ system and Supersonic™ motor drive for quiet operation.

HERE WE HAVE A NEW. DIGITRAX ZEPHYR XTRA STARTER SET, LOCO NET, EVERYTHING NEEDED TO RUN DCC EQUIPMENT.AND MUCH MORE.

Digitrax #DZ126IN N Scale DCC Decoder. Digitrax 1.0 amp, 2 function 6-pin plug-in decoder. Replaces DZ125IN decoder.Fits Fox Valley N scale DCC ready locomotives and other. Complete instructions included.

Digitrax SDN136PS N Scale DCC Sound Decoder. N (and small HO) scale 1.0 amp (2 amp peak), 3 function, universal sound decoder by Digitrax with 8-pin DCC plug and harness. Preloaded with selectable steam (default) and SD38-2 diesel locomotive sound schemes (other schemes may be downloaded from Digitrax).

SE8C Plug 'N Play Signal Decoder make it easy to add prototypical signaling to your layout. The SE8C can drive as many as 32 signal heads with many popular LED signal types. A computer and third party software are necessary to realize the full feature potential of the SE8C.

Digitrax SoundFX® Sound System. Downloadable Sound with Digitrax PR3 and SoundLoader 2.0 software. Item:DCC Decoder Fits Kato N Scale SD40 and similar Locomotives. Fits Kato N Scale SD40 and similar Locomotives.

Item:DZ126T 1 Amp Tiny Series 6 decoder for Z, N & HO. Digitrax LocoMotion. ▪Digitrax LocoMotion. The Digitrax LocoMotion System makes them run like the real thing, too! ▪Program CVs using any Digitrax Compatible Control system without having to buy any extra equipment.

Digitrax Easy Connect 9 Pin Harness. Scale: HO. Get Supersized Images & Free Image Hosting. Auctiva's FREE Counter.

HERE WE HAVE A NEW. DIGITRAX UT4 UTILITY THROTTLE, LOCO NET ,WALKAROUND. AND MUCH MORE .

Item:EVOD Evolution Duplex System 5/8 V Start Set DCS210, DT500D, UR92 & PS615. DT500D Super LocoNet Throttle (Duplex Radio). DCS210 comes with 3 LocoNet ports for Easy expandability. Everything you need to get started with Advanced Digitrax Command Control.

Scale: N / Z / HO. Fits Many Z, N and HO Scale Locomotives. 1.0 Amp/1.5 Amps Peak. Z/N/HO Scale. 2 FX3 Functions, 0.5 Amp. Save time & money with. FREE Auctiva Image Hosting. Auctiva's FREE Counter.