• Hantek HT25 8' Secondary Ignition Capacitive Auto Pickup Probe X10000 pico scope

    To test a spark ignition secondary overlapping wave, overlapping wave parameters, thus achieved the detection, the diagnosis engine ignition position, make each cylinder ignition voltage changing with time directly from the oscilloscope display. The loot line has three end, a joint meet oscilloscope for BNC use, a for use, a clip grounding to pick high-voltage gleaned clip with. Loot clincher over is a attenuator, used for loot high-pressure attenuation for low pressure, thus protecting oscilloscope not electrify impact. please note: (1)test clips shall not directly clip in spark plug, should be caught in the connection of the spark plugs of insulation wire, in order to prevent the breakdown and causing a shock. (2)to distance other high-voltage at least 2 inches apart, lest produce inter.
    AU $18.35
    Was: Previous priceAU $19.95
    Free postage
  • Hantek HT307 Acupuncture Back Probe Pins Set Test Accessories Repair Tool H8U4

    This acupuncture probe is a back pinning, piercing and repairable probe. This set includes 5pcs complete acupuncture probes, 2pcs screws, and 20pcs replacement needles. The set of 5 probes also comes with 20 replacement pins, there's no need to replace the whole probe.
    AU $8.19
    eBay Premium Service
    Free postage
    From China
    51 sold
  • Hantek Coil-on-Plug extension leads(HT308) Automobile Diagnostic Oscilloscope

    COP Extension Cord (HT308) Simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug (COP) ignition systems. Contents: 1pc X Coil-on-Plug Extension Cord and 1pc X Earth Cord. Coil-on-Plug extension cord with earth cord are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension cords are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads. Contents: 1pc X Coil-on-Plug Extension Cord 1pc X Earth Cord.
    AU $35.50
    Free postage
  • Hantek PP-150 100 MHz Oscilloscope X1-X10 Probe Kit

    Description: Hantek PP-150 100 MHz Oscilloscope X1-X10 Probe Kit Description: - The Hantek PP-150 100 MHz Oscilloscope Probe Kit provides a probe tip, ground lead, several marker rings, tip locating sleeve, and adjustment tool. The probe is a passive, low-impedance attenuation probe. - The probe has been designed and calibrated for use on instruments having an input impedance of 1MΩ paralleled by 20pF. It may also be recalibrated for use on instruments having an input capacitance of 15 to 40pF. - The probe incorporates a two position (1X, 10X) slide switch in the compensating network and cable length of 1.2 meters. Electrical Characteristics - Temperature -15°C to 70°C - Attenuation: X1, X10 - Input Capacity: 85pF~115pF, 18.5pF~22.5pF - Oscilloscope Input capacity: 15pF~40pF - In.
  • Hantek PP-200 X1 X10 200MHz Oscilloscope Clip Passive Probe BNC Port Probe Kit

    The Hantek PP-200 200 MHz Oscilloscope Probe Kit provides a probe tip, ground lead, several marker rings, tip locating sleeve, and adjustment tool. The probe is a passive, low-impedance attenuation probe. - The probe has been designed and calibrated for use on instruments having an input impedance of 1MΩ paralleled by 20pF. It may also be recalibrated for use on instruments having an input capacitance of 15 to 40pF. - The probe incorporates a two position (1X, 10X) slide switch in the compensating network and cable length of 1.2 meters. Electrical Characteristics - Temperature -15°C to 70°C - Attenuation: X1, X10 - Input Capacity: 85pF~115pF, 18.5pF~22.5pF - Oscilloscope Input capacity: 15pF~40pF - Input Resistance: X1: 1MΩ±2% X10: 10MΩ±2% - Bandwidth: X1: DC-6MHz.
    AU $21.11
    Was: Previous priceAU $22.95
    Free postage
  • Hantek HT201 20:1 Passive Attenuator 300V Max For Pico Hantek & Others

    The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscope products. Hantek HT201 1.053M Input Resistance 10MHz Bandwidth Signal Attenuator.
    AU $18.35
    Was: Previous priceAU $19.95
    Free postage
  • Hantek PP-200 x1 x10 200MHz Digital Oscilloscope Clip Probe Kit Test Leads SG

    Nail Care, Manicure& Pedicure. Oral Care. Metal working. Drill bits. Integral injection molding makes the usage more flexible and the oscilloscope able to adapt more testing situations. Attenuation ratio: 1x and 10x optional.
    AU $15.19
    From Hong Kong
    Was: Previous priceAU $15.99
    Free postage
  • Hantek HT307 5pcs Automotive Diagnostic Test Accessory Back Pinning Probes H8R5

    This acupuncture probe is a back pinning, piercing and repairable probe. This set includes 5pcs complete acupuncture probes, 2pcs screws, and 20pcs replacement needles. They can be used as pin-tip probes while working with small circuit boards.
    AU $8.48
    eBay Premium Service
    Free postage
    From China
  • Hantek 20:1 Attenuator HT201 10MHZ Input Res1.053MHZ for DSO3064 Automotive SG

    Metal working. BI 20%. BI 10%. BI 15%. HT201 20:1 Signal Passive Attenuator 10MHZ Bandwidth For Oscilloscope ark. BI 25%. BI 30%. Passive attenuator with 20:1 attenuation, if input a 20V signal, it can output a 1V signal.
    AU $9.04
    From Hong Kong
    Was: Previous priceAU $9.52
    Free postage
  • Hantek HT307 Back Pinning Probes Small Diameter Needles Piercing Probes Set 83AO

    This acupuncture probe is a back pinning, piercing and repairable probe. This set includes 5pcs complete acupuncture probes, 2pcs screws, and 20pcs replacement needles. Its small diameter, extra sharp pin makes it ideal for piercing the insulation on small gauge wires.
    AU $8.48
    eBay Premium Service
    Free postage
    From China
    86 sold
  • Hantek Max.600V DC Peak AC x1 x10 60MHz 10MΩ Oscilloscope Clip Probe with M8Y0

    X10: <600V DC Peak AC. Integral injection molding makes the usage more flexible and the oscilloscope able to adapt more testing situations. Attenuation ratio: 1x and 10x optional. Compatible with domestic and international digital and analog oscilloscopes in relevant frequency.
    AU $7.19
    From China
    Free postage
  • 1pcs Hantek 20:1 Attenuator HT201 10MHZ Input Res1.053MHZ for DSO3064 Automotive

    Yard, Garden & Outdoor Living. Passive attenuator with 20:1 attenuation, if input a 20V signal, it can output a 1V signal. When used in an oscilloscope to measure an inductive signal, such as a jet nozzle and a primary ignition, it provides enhanced input overload protection.
    AU $8.89
    From Hong Kong
    Free postage
  • Hantek HT25 8' Secondary Ignition Capacitive Auto Pickup Probe X10000 pico scope

    To test a spark ignition secondary overlapping wave, overlapping wave parameters, thus achieved the detection, the diagnosis engine ignition position, make each cylinder ignition voltage changing with time directly from the oscilloscope display. The loot line has three end, a joint meet oscilloscope for BNC use, a for use, a clip grounding to pick high-voltage gleaned clip with. Loot clincher over is a attenuator, used for loot high-pressure attenuation for low pressure, thus protecting oscilloscope not electrify impact. please note: (1)test clips shall not directly clip in spark plug, should be caught in the connection of the spark plugs of insulation wire, in order to prevent the breakdown and causing a shock. (2)to distance other high-voltage at least 2 inches apart, lest produce inter.
  • Hantek PP-150 100 MHz Oscilloscope X1-X10 Probe Kit

    Description: Hantek PP-150 100 MHz Oscilloscope X1-X10 Probe Kit Description: - The Hantek PP-150 100 MHz Oscilloscope Probe Kit provides a probe tip, ground lead, several marker rings, tip locating sleeve, and adjustment tool. The probe is a passive, low-impedance attenuation probe. - The probe has been designed and calibrated for use on instruments having an input impedance of 1MΩ paralleled by 20pF. It may also be recalibrated for use on instruments having an input capacitance of 15 to 40pF. - The probe incorporates a two position (1X, 10X) slide switch in the compensating network and cable length of 1.2 meters. Electrical Characteristics - Temperature -15°C to 70°C - Attenuation: X1, X10 - Input Capacity: 85pF~115pF, 18.5pF~22.5pF - Oscilloscope Input capacity: 15pF~40pF - In.
    AU $12.83
    Was: Previous priceAU $13.95
    Free postage
  • Hantek Coil-on-Plug extension leads(HT308) Automobile Diagnostic Oscilloscope

    COP Extension Cord (HT308) Simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug (COP) ignition systems. Contents: 1pc X Coil-on-Plug Extension Cord and 1pc X Earth Cord. Coil-on-Plug extension cord with earth cord are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems. Coil-on-Plug extension cords are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads. Contents: 1pc X Coil-on-Plug Extension Cord 1pc X Earth Cord.
    AU $18.35
    Was: Previous priceAU $19.95
    Free postage
  • Hantek Back Test Probe Pins Set Automotive Diagnostic Test Accessories V3E2

    The set of 5 probes also comes with 20 replacement pins, there's no need to replace the whole probe. This acupuncture probe is a back pinning, piercing and repairable probe. This set includes 5pcs complete acupuncture probes, 2pcs screws, and 20pcs replacement needles.
    AU $8.47
    From China
    Free postage
Got one to sell?

Got one to sell?

Get it in front of 160+ million buyers.

78 items found from eBay international sellers

Tell us what you think - opens in new window or tab