Hobby RC Model Vehicle Body Parts & Interior for OS

One Nitro Tuner Dial for OS 30 and many other Nitro Engine with the High-speed needles casing Diameter that is about 7.5 mm. Installing onto carburetor high-speed needles. Now you are able to rich up or lean out your engine an exact amount.

Glow plug wrench, HCAP2550. This is the O.S. #7 Medium Hot Glow Plug for 2-Stroke Engines. O.S. #7 Medium Hot Glow Plug with gasket. type flight. Slightly hotter heat range than the O.S. #8 plug. Also great all around plug for most 2-stroke airplane, helicopter and.

This is a Sullivan Products SULS681 Heavy Duty Tiger Drive Electric Start Adapter for nitro engines equipped with an 8mm bearing. This includes OS. 12-.21 nitro engines. This unit replaces the pull start on many R/C cars, boats, and helicopters - allowing the use of a hand-held starter or power drill to start your vehicle.

This is the O.S. Max LC3 Long Reach Hot Glow Plug. Designed for use in. 12-.15 and. 18 size engines used in monster trucks such as the original and newer 2.5 and 3.3 Traxxas T-Maxx trucks. Like all O.S. Max glow plugs, the LC3 is tough enough to take the heat and provide hassle-free starts and outstanding durability.

Stay the same! The ad photo is a sample. Find THOUSANDS of RC parts.

This is a O.S. Engines T-Series RP8 Cold Heat Range Turbo Glow Plug.

Find THOUSANDS of RC parts.

This is the O.S. Max. 21 TM Engine with the T-Maxx Manifold. This engine will be a direct drop in for the Traxxas 2.5 and 3.3 T-Maxx. This can also be made to fit the Traxxxas Jato, Nitro 4-Tec, Nitro Rustler, or Revo with the proper manifold and carb linkage.

This is a replacement small O-ring that goes on the idle set screw.

NOTE: You will need to detach the old connecting rod and re-attach it to the new piston during replacement. We recommend that when you replace the piston/sleeve on any engine, you also change the connecting rod and wrist pin clips.

O.S. went back to the drawing board to give the Speed R2101 a facelift, resulting in the Speed R2102. But, the key features that have made Speed engines popular among enthusiasts are still here, including the DLC coated and tungsten weighted crank and a ceramic rear bearing.

This is a replacement O.S. B2101 Speed Outer Cooling Head. This machined low center-of-gravity cooling head is laser-etched with cool graphics, and provides lower weight and improved cooling over previous generations.

This is a replacement O.S. Engines Connecting Rod, intended for use with the O.S. 28XZ Truggy Engine (#OSM12830). The connecting rod attaches between the crankshaft and the piston. If you are replacing the piston/sleeve in your engine, it is always a good idea to replace the connecting rod at the same time to avoid premature failure due to wear.

This is a replacement thermo carb insulator gasket for O.S. 20K/21C/20L/21H/21J carburetors. This is the small gasket that goes between the carburetor and the engine crankcase to stop heat transfer from the crankcase to the carburetor.

This is an optional O.S. Induction Silencer. Weight: 0.67oz (19g). NOTE: Uses OSMG2351 replacement Foam Filters. Zip tie. Height: 1.96" (50mm). Diameter: 1.9" (47.5mm).

This is a set of two replacement O.S. Piston Pin Retainer Clips. These clips are used to retain the wrist pin inside the piston, which secures the piston to the connecting rod. It is recommended that you replace them with new clips to prevent possible failure caused by used clips.

This is a replacement O.S. Cooling Head, and is intended for use with the O.S. 21XZ-B Speed engine.

Installing onto carburetor high-speed needles. Now you are able to rich up or lean out your engine an exact amount. CNC Machined from 6061 Aluminum and Blue anodized with Laser Engraved Dial fit around the high-speed needles.

This is a replacement O.S. Head Button, and is intended for use with the O.S.21XZ-B.

The 20J carburetor has both high-speed and idle needles. Includes: mount, outdrive unit, E-2050-2 removable muffler, starter cone, #20J carb, #8 glow plug, steering bracket, throttle link assembly & 42 x 1.2 carbon prop.

This is a replacement one way rear bearing for the O.S. 18 TZ/TX based engines, and 30 VG based engines.

This is a replacement connecting rod for O.S.21 VZ-B V-Spec engines.

This is a set of ten O.S. Engines 3x18mm Cap Screws, intended to secure the engine cooling head to the crank case of the O.S. 28XZ Truggy Engine.

This is a Set of 4 Replacement FOAM elements for the OS #202 Super Air. Cleaner (OSMG2384). Each element is pretreated with a special lubricant which. Includes: 4 pretreated blue foam filter elements (42mm dia. ).

This is a replacement O.S. Speed 21XZ-B Spec II Cooling Head. This head has been redesigned with V-shaped fins for lower CG and efficient cooling.

The O.S. #A3 glow plug is similar to the #8 plug only hotter. This is a HOT heat range two-stroke glow plug for all engine applications. Hot heat range plug for most model engine applications. The ad photo is a sample.

This is the Large Super Filter for Glow Fuel from O.S. Max. INCLUDES: One Large Fuel Pickup Filter. This pickup filter is installed inside a refueling container. FEATURES: Dense fiberous filter element.

NOTE: These O-Rings can also be used for other applications where a 3x6mm silicone o-ring is needed. This is a set of O.S. Engines Mixture Control Valve O-ring's, intended for use with the #6H and #7D OS carburetors.

This is the OS Speed Hyper Flywheel Set for Mugen. INCLUDES: One hyper flywheel with flywheel collar. Steel constructed flywheel collar and pins. FEATURES: Aluminum construction, black anodized in color.

Part Number: OSM79871055. These are 2.6mm x 18mm Carb Screws for the O.S. FS56-a Engine. Item condition. We will arrange to replace your item and pick-up the incorrect item as quickly as possible. The item must be received in the same condition as it was sold and include all accessories, if applicable.

This is a replacement O.S. Needle Holder Assembly, and is intended for use with the O.S. XZ-B, and XZ-B Speed. 21 engines.

It has a 42MM diameter The Pitch is 1.2. Diameter: 42MM Pitch: 1.2 Shaft Size: 5MM. This is a 2-Bladed Carbon Fiber Prop for the OS. 21XM Outboard. New and unused. It s Black.

Find THOUSANDS of RC parts.

This is a replacement carburetor retainer for O.S. 30 VG engines.

This is a set of replacement dust caps for O.S. 21 VZ-B and V-Spec engines. This includes a smaller cover for the carburetor neck, a larger cover for the rear exhaust outlet, and a small cover for the main needle valve fuel inlet.

This is a replacement O.S. Speed 21XZ-B Spec II Cover Plate.

This is a O.S. Engines T-Series RP7 Medium Heat Range Turbo Glow Plug.

This is a replacement O.S. B2101 Speed Cover Plate.

This is a replacement carburetor sealing washer for the O.S.21 VZ-B V-Spec engines.

This is the O.S. T-2060SC WN One Piece Tuned Pipe With Manifold. This pipe also features a welded nipple so you won't have to worry about losing back pressure due to an air leak.

This is the O.S. Engines OSM21682500 Metering Needle for 12F and 12 FB Carburetors used in the O.S Engines 12XZ Speed Engines. Metering Needle for 12F/FB Carburetors on 12XZ Speed Engines. (1) Metering Needle.

This is a replacement O.S. Cover Plate Gasket, and is intended for use with the O.S.21 XZ-B.

This is a replacement O.S. Throttle Stop Screw, and is intended for use with the O.S. XZ-B, and XZ-B Speed. 21 engines.

This is a replacement O.S. High Speed Needle, and is intended for use with O.S. 21H, 21J, 21C, 21E, 21F, 21B, 20K, and 20E carburetors.

This is a replacement O.S. 3x3mm Set Screw.

This is a replacement high speed metering needle for the O.S. VZ-B V-Spec carburetor.

This is a replacement O.S. 12-30 Class Dust Cap Set. These are compatible with the O.S. Speed R2101 and 21XZ-B V2 engines.