5stars
54ratings4stars
8ratings3stars
4ratings2stars
0rating1star
0rating
Would recommend100% agree
Good value100% agree
Good quality100% agree
51 reviews
2018 Ram 2500 Pocket Fender Flares from K2 Motor
These flares appear to be of the same quality as the more expensive Bushwacker and King brands. They are nearly 1/8” thick and very precise fitment. The stainless steel bolts are the Torx type (like the previously mentioned brands) and the heads are nearly the size of a dime in comparison. The fit and finish are top notch as well resulting in no trimming or fitment being required. They come with all hardware and instructions. Each flare is individually bubble wrapped and labeled to indicate proper placement. At 18% of the cost compared to the “major” brand name you can’t go wrong these in my opinion. Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Ehhh they're ok
You get what you pay for. A bit bigger longer than it's supposed to but not bad for the price. They do look and say bolt on... they don't actually bolt on to the side of the truck they bolt on to the liner.
2 of the strips it comes with are shorter which it doesn't say they are so didn't notice until I had one too short for the back.Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Nice quality
Very nice quality and very easy installation. I installed them on my 2017 Ram 2500. Only complaint was the instructions were kind of vague and recommended using the screws that came in package. I used my stock screws which seemed more secure. All in all, very nice product. Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Great quality and fit
I just installed these flares on my 2010 Ram 2500 and the look and fit awesome! They were packaged very well and arrived in perfect condition with all hardware and detailed installation instructions. The rubber seal that you install on each flare is the most tedious part of the install. Be patient and try to get all the twists out of the seal before you start applying it on the flare. The stainless hardware looks and fits great and once the rubber seal is installed on the flares it's a 30 minute job to install on the vehicle. Plan on at least 1.5 hours to do the job. Very high quality flares and half the cost of Lund and Bushwacker. I've owned both and these are the EXACT same quality for half the price!Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Not bad!
The flares seem to be of good quality. I kind of expected them to fail/crack when tighten up up the bolts/screws. Fitment is pretty good. You really have to put pressure on and up to get them snug to the truck. The bottoms on the rear have some gaps. Nothing I could do to get them snug. 2 issues for me...the directions stink. I should have just ditched them. They make it complicated because they didn't match my truck somehow. I preferred to use the factory fasteners bc they large washers give better contact. For me, basically, take out the factory bolts and install with them. Use a couple of theirs where there aren't factory. Overall, satisfied.Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Installed on 2011 Dodge 2500
These were a perfect fit and nice quality. It was time consuming installing the rubber seal but well worth the time. The only thing that needs to be changed is the size of the black screws that came with the product. They work for the clips that are used but are smaller than the stock bolt that holds the fender wall in. The instructions say to replace some of the stock bolts with the screw. The screws are to small and will not tighten. I reused all the stock bolts so it was no big deal. Over all install was pretty simple and they look great.Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Very happy
Great product easy to install. The 3m adhesive strips inside the rubber lining should be pressed before removing the red plastic to make sure there is a good bond since I had a few section peel away from the flare removing the red plastic. Other then that amazing price amazing product. I wish all companies made there product with this quality and pricing.Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Worth it
These went on with zero issue. I didn't have to remove any badges, every hole lined up. I didn't remove any of the 3M tape cover until I had the gasket completely on. Makes life so much easier. There was almost a foot of gasket leftover when I was finished. Gasket doesn't go around the entire thing, just on the areas that would contact the paint. Fit and finish is excellent. Buy a set, you won't be disappointed!!! Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Awesome product
These were surprisingly well made and easy to install. I've had other brand (higher priced) flares before and these are just as good if not better. Definitely won't be disappointed, all the way down to the stainless Torx bolts (for looks only) actually uses existing bolt holes in truck fender wheel no drilling requiredRead full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Impressed with the fit.
I installed unpainted and they look great. Fit nice and tight. You do have to reuse some oe fasteners which wouldn’t be a problem if mine weren’t rusted but I made it work. Overall very impressed, especially for the price. I like that they don’t stick out too far and look good even without spacing out the stock wheels. Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor
Fit perfectly, outstanding price!
Quality flares for an unreal price. I took a gamble on these flares to avoid the Bushwhacker flare cost of $750.00 for a set. Glad I did. Fit perfectly on my 2015 Dodge Ram 2500. Easy install too. I would highly recommend this product. All around best money I've spent.Read full review...
Verified purchase: Yes | Condition: new | Sold by: k2motor